A Cone Penetration Test (CPT) is commonly used to determine the subsurface stratigraphy in situ (in place) and to estimate geotechnical parameters of the materials present. Geotechnical engineers typically use a CPT test to determine the necessary construction requirements for infrastructure – roadbeds, bridges, buildings. Due to the sensitive electronics inside the cone, it must be pushed to depth by static push methods. The CPT test method consists of pushing an instrumented cone into the ground at a controlled 2 cm/sec push rate. Common measurements being collected are cone tip pressure, sleeve friction, pore pressure and tilt angle. Additional sensors can be added like seismic, or other geo-environmental logging tools.
= Tool String Diagram (TSD)
Having offered CPT equipment for decades, Geoprobe® has come to understand how innovative and ahead of their time the first generation of CPT Cones were. These independently gauged compression cones deliver high resolution digital data. The Classic line even introduced wireless transmission via sound waves. This was a very common method for years, offered as an alternative to cones requiring a cable through the push rods.
Today we offer the next generation of CPT technology - NOVA. The NOVA CPT test cone introduces higher resolution, more robust construction and improved accuracy. NOVA CPT delivers improved durability and sensitivity in an instrumented cone.
The Geotech AB NOVA CPT system has always been unique in the geotechnical industry and is known for its cordless data transmission system: a constant digital stream of data is sent to the surface through the sounding rods. No cable through the rods is needed in the cordless setup.
For more than 20 years, Geoprobe Systems® has teamed up with Geotech AB of Sweden to be the exclusive U.S. distributor for Geotech AB Cone Penetration Testing tools for geotechnical and environmental studies. We also provide the service and support, offering repair and calibration services.
The cordless or corded NOVA CPT test cones can be used from a variety of push platforms to provide continuous data, repeatable penetration results, and cost savings over traditional boring and sampling methods. NOVA Cones adhere to the national standards for construction (ASTM D-5778 Standard Test Method for Performing Electronic Friction Cone and Piezocone Penetration Testing of Soils, as well as ISO 22476-1-11:2004).
Advantages of CPT
CPT test primary measurements include tip resistance(qc), sleeve friction(fs), and pore pressure(u). Tip resistance is a measurement of soil hardness, sleeve friction is an indication of the soil cohesive strength commonly seen with clays and pore pressure is related to the pressure generated as the cone is advanced as well as an indication to the amount of clay in the formation.
The cordless CPT does not require a cable for data transmission to the surface. Inside the cone, the digital coded signal is converted to an acoustic signal which is transmitted along the steel of the drill rods to the surface. Sound signals are received by a microphone at the surface which transmits the signal to a PC via a computer interface (Fig. 2).
A corded CPT test system does not require the microphone as the data will travel through the cable to the surface computer interface and laptop computer. A simple and cost effective 4-wire cord is used in this case, connecting through a cable adapter to the CPT Cone.
Data interpretation software, called CPT-PRO, completes your CPT investigation.
Features & Options
Having offered CPT equipment for decades, Geoprobe® has come to understand how innovative and ahead of their time the first generation of CPT Cones were. These independently gauged compression cones deliver high resolution digital data. The Classic line even introduced wireless transmission via sound waves. This was a very common method for years, offered as an alternative to cones requiring a cable through the push rods.
Today we offer the next generation of CPT technology - NOVA. The NOVA CPT test cone introduces higher resolution, more robust construction and improved accuracy. NOVA CPT delivers improved durability and sensitivity in an instrumented cone.
The Geotech AB NOVA CPT system has always been unique in the geotechnical industry and is known for its cordless data transmission system: a constant digital stream of data is sent to the surface through the sounding rods. No cable through the rods is needed in the cordless setup.
For more than 20 years, Geoprobe Systems® has teamed up with Geotech AB of Sweden to be the exclusive U.S. distributor for Geotech AB Cone Penetration Testing tools for geotechnical and environmental studies. We also provide the service and support, offering repair and calibration services.
The cordless or corded NOVA CPT test cones can be used from a variety of push platforms to provide continuous data, repeatable penetration results, and cost savings over traditional boring and sampling methods. NOVA Cones adhere to the national standards for construction (ASTM D-5778 Standard Test Method for Performing Electronic Friction Cone and Piezocone Penetration Testing of Soils, as well as ISO 22476-1-11:2004).
Advantages of CPT
CPT test primary measurements include tip resistance(qc), sleeve friction(fs), and pore pressure(u). Tip resistance is a measurement of soil hardness, sleeve friction is an indication of the soil cohesive strength commonly seen with clays and pore pressure is related to the pressure generated as the cone is advanced as well as an indication to the amount of clay in the formation.
The cordless CPT does not require a cable for data transmission to the surface. Inside the cone, the digital coded signal is converted to an acoustic signal which is transmitted along the steel of the drill rods to the surface. Sound signals are received by a microphone at the surface which transmits the signal to a PC via a computer interface (Fig. 2).
A corded CPT test system does not require the microphone as the data will travel through the cable to the surface computer interface and laptop computer. A simple and cost effective 4-wire cord is used in this case, connecting through a cable adapter to the CPT Cone.
Data interpretation software, called CPT-PRO, completes your CPT investigation.
If you do a geotechnical boring it requires a lot of tooling, time, work, and sweat. With CPT test it's so much simpler. We completed half the borings with cone penetration testing, which cuts time and increased profit substantially. This also provided comparable data.
- Matthew Sick, Operator, Geotechnics Soil and Material Testing, Missouri
Features of NOVA CPT
There's lots more to be said about this innovative CPT equipment. To request more detailed information about how this CPT system can work for you request info from us or visit Geotech AB's website.
Seismic Cone Penetration Testing (SCPT) sounding provides a rapid and cost-effective method for directly measuring shear wave velocity of soils in situ. Shear wave velocity is used as an index of liquefaction resistance since both are influenced by many of the same factors. Alternatives to using SCPT for these geotechnical analysis can require laboratory testing or less reliable, highly empirical assessments.
SCPT shear wave velocity measurements are used in these evaluations:
The seismic CPT equipment is used as an add-on to our traditional NOVA CPT system. CPT data is taken in the same push that seismic information is generated.
The SCPT probe consists of a seismic section threaded to a standard NOVA CPT probe. The CPT probe records tip resistance, sleeve friction, pore pressure, and tilt angle while the seismic section is used to measure the shear wave velocities. The amount of data that is measured is too great for cordless transmission, so the SCPT probe is run with a data cable through the rods.
SCPT Benefits include:
How does a SCPT test work?
Some testing applications require that the tooling is pushed into the ground instead of hammered. To do this, the power of the machine's probe cylinder is used to advance the rod string instead of energy from the hammer. To achieve any sort of depth, a suitable reaction force must be used to balance the pushing capacity of the rig. This means that you either need a really heavy rig or you need to anchor your machine.
The Geoprobe® 2060CPT is a 20 ton rated static push Cone Penetration Testing platform. The hydraulic push clamp and press advance the cone with up to 20 tons of downforce. When retracting the tool string, the 2060CPT has 30 tons of pullback. A hydraulic bottom clamp keeps rods from slipping back down hole when the push clamp is released during retrieval of the tool string. An optional 6712DT mast can be mounted on the porch end of the 2060CPT. This allows for coring, conventional soil sampling, shallow drilling for soil verification, and pre-drilling.
> Learn More
The 20 CPT press from Geoprobe® is a flexible mast option designed specifically for performing cone penetration tests. Bracket options allow for mounting to various skid steer loaders or the Geoprobe® 6712DT. When anchored, the press has 20 tons of hydraulic downforce and 30 tons of pullback. The light weight system and small footprint allow this setup to be easily transported from location to location. This also enables the press to access sites where surface conditions will not support a larger, heavier machine.
Learn More
The Geoprobe® 3230DT combo rig has the ability to efficiently sample the subsurface using both direct push and rotary drilling techniques and then quickly transition to pushing CPT tooling. Anchors are installed using the CB combo head and the CPT system is automatically pushed at a rate of 2 cm / second using the same head. With the 3230DT, drillers have multiple drilling methods at their fingertips.
Learn More
The Geoprobe® 7822DT is designed to easily switch between multiple sampling and logging methods, including pushing CPT tooling. Anchors are installed with the augerhead to provide the reaction force needed for the up to 15 tons of push typical for this platform. Using an optional head feed control kit, automatic rate control provides cone advancement at the standard 2 cm per second. Switching between drilling tasks and pushing CPT is quick on the 7822DT and only takes a few additional components.
Learn More
The 3100GT geotechnical drill rig can be setup for CPT by using a few simple anchoring components: a rod guide, anchor, and anchor bridge. Switching from geotechnical drilling to pushing CPT is a quick and simple process. Automatic head feed rate control advances the cone at a steady 2 centimeters per second specified by ASTM Standard D5778. This provides hands-free operation during advancement of each rod.
Learn More
Operators of Geoprobe® Direct Image® Optical Image Profiler/Optical Image Hydraulic Profiling Tool (OIP/OIHPT) tooling can add CPT to their data stream in one of these push only tool combinations. Along with the CPT geotechnical data the operator will also collect soil conductivity with electric conductivity (EC), formation permeability measurements with HPT, and UV fluorescence of non-aqueous phase fuel hydrocarbons (NAPL) with the OIP.
The OIHPT tool allows an operator to map NAPL fuels/oils by induced fluorescence from an onboard UV LED or Green laser diode with images being captured by an onboard CMOS camera. Mapping the vertical and horizontal extents of NAPL contamination along with soil EC and HPT injection pressure provides understanding of soil types, permeability and migration pathways.
> Learn More: OIP
The Membrane Interface Hydraulic Profiling Tool (MIHPT) allows an operator to map dissolved phase to NAPL levels of hydrocarbon or solvent based volatile organic compounds (VOCs). Operators around the world use MIP technology to hunt out contaminant source areas and/or delineated plume extents. The coupled EC and HPT sensors again allow for the collection of soil EC and HPT injection pressure to understand of soil types, permeability and migration pathways.
> Learn More: MIP
ID: 5533
ID: 268
ID: 1933
Click on a section below to view information.
Passionate about delivering exceptional geotechnical, environmental, and instrumentation exploration services, the TERRACON CONSULTANTS INC office in Savannah, Georgia, went from being without in-house drilling resources in 2021 to running three Geoprobe®
ID: 13403 | Date:
Engineers who had gained valuable geotechnical experience working for the US Army Corps of Engineers Vicksburg District and the Waterways Experiment Station in Vicksburg, Mississippi, launched BURNS COOLEY DENNIS in 1985. Now with a staff of more than 60,
ID: 13399 | Date:
Adding 20CPT Skid Steer and CPT equipment provides economical way to gain footing in the CPT market.
ID: 12388 | Date:
Seismic CPT module offers processing and procedural advantages to maximize confidence in field testing.
ID: 12387 | Date:
Rope thread minimizes rotations required to make a joint while size fits inside 2.25-inch rod often used as a conductor casing.
ID: 5777 | Date:
Since 1987, Geoprobe® has manufactured innovative drilling rigs and tooling - engineered for efficiency and safety - simplifying drillers’ jobs and empowering their companies to succeed as productive and profitable leaders in the industry. When you partner with Geoprobe® you receive:
Engineering and building industry-leading drilling rigs, tooling, and techniques for the technical driller based on your needs to work safer and more efficiently.
Ensuring drilling rigs and tooling are created in conjunction – with consistent quality – to collect the highest-quality information with the most accurate result to get you to, into, and through the job efficiently.
Equipping you to do your best job and keeping you in the field via one-on-one expert sales and service technicians manning live support phone lines, shipping necessary parts same-day.
Having offered CPT equipment for decades, Geoprobe® has come to understand how innovative and ahead of their time the first generation of CPT Cones were. These independently gauged compression cones deliver high resolution digital data. The Classic line even introduced wireless transmission via sound waves. This was a very common method for years, offered as an alternative to cones requiring a cable through the push rods.
Today we offer the next generation of CPT technology - NOVA. The NOVA CPT test cone introduces higher resolution, more robust construction and improved accuracy. NOVA CPT delivers improved durability and sensitivity in an instrumented cone.
The Geotech AB NOVA CPT system has always been unique in the geotechnical industry and is known for its cordless data transmission system: a constant digital stream of data is sent to the surface through the sounding rods. No cable through the rods is needed in the cordless setup.
For more than 20 years, Geoprobe Systems® has teamed up with Geotech AB of Sweden to be the exclusive U.S. distributor for Geotech AB Cone Penetration Testing tools for geotechnical and environmental studies. We also provide the service and support, offering repair and calibration services.
The cordless or corded NOVA CPT test cones can be used from a variety of push platforms to provide continuous data, repeatable penetration results, and cost savings over traditional boring and sampling methods. NOVA Cones adhere to the national standards for construction (ASTM D-5778 Standard Test Method for Performing Electronic Friction Cone and Piezocone Penetration Testing of Soils, as well as ISO 22476-1-11:2004).
Advantages of CPT
CPT test primary measurements include tip resistance(qc), sleeve friction(fs), and pore pressure(u). Tip resistance is a measurement of soil hardness, sleeve friction is an indication of the soil cohesive strength commonly seen with clays and pore pressure is related to the pressure generated as the cone is advanced as well as an indication to the amount of clay in the formation.
The cordless CPT does not require a cable for data transmission to the surface. Inside the cone, the digital coded signal is converted to an acoustic signal which is transmitted along the steel of the drill rods to the surface. Sound signals are received by a microphone at the surface which transmits the signal to a PC via a computer interface (Fig. 2).
A corded CPT test system does not require the microphone as the data will travel through the cable to the surface computer interface and laptop computer. A simple and cost effective 4-wire cord is used in this case, connecting through a cable adapter to the CPT Cone.
Data interpretation software, called CPT-PRO, completes your CPT investigation.